Industrial Development Guide / Updated November 2026
Industrial Outdoor Storage Development Cost in 2026: What an IOS Truck and Equipment Yard Costs Per Acre
Industrial outdoor storage development cost in 2026 runs about $175,000 to $425,000 per acre for a compacted aggregate yard, $325,000 to $650,000 per acre for heavy-duty asphalt, and $550,000 to $950,000 per acre for concrete, covering surface, grading, stormwater, fencing, gates, lighting, cameras, utilities, and soft costs. A pre-engineered shop and office adds about $150 to $275 per SF. Land and fees are extra.
- Per acre, all in: $175,000 to $425,000 for aggregate, $325,000 to $650,000 for asphalt, $550,000 to $950,000 for concrete, excluding land and building.
- Demand is real: Newmark reports IOS rents up 123 percent since 2020, and KBRA research put IOS vacancy at 2.5 percent versus 6.7 percent for traditional industrial.
- Gravel is not a stormwater loophole: many jurisdictions count compacted gravel as impervious, so detention on an aggregate yard costs nearly what it does on asphalt.
- Concrete only where it earns it: ACI 330 Category D truck lanes run about 6.5 to 9 inches thick; use concrete for aisles, dolly pads, and container handler lanes, not the whole yard.
- The building is small: keep coverage at 5 to 15 percent and budget $150 to $275 per SF for a finished PEMB shop and office.
- Zoning first: 8 foot screening, barbed wire limits, and conditional use hearings can add $100,000+ and 6 months before any dirt moves.
How much does it cost to develop an IOS yard per acre in 2026?
Industrial outdoor storage development cost in 2026 runs about $175,000 to $425,000 per acre for a compacted aggregate yard, $325,000 to $650,000 per acre for heavy-duty asphalt, and $550,000 to $950,000 per acre for a concrete truck yard. Those numbers are site work only: surface, grading, stormwater, fence, gates, lighting, cameras, utilities, and soft costs. Land and the shop or office building are separate.
The spread is wide because two IOS yards with the same acreage can be completely different projects. A flat, already-graded parcel in an industrial park with a regional detention pond is a surfacing job. A raw parcel that needs cut and fill, an on-site detention basin, an 8 foot screen wall, and a three-phase service extension is a full civil project before a single trailer parks on it.
| Yard type | Surface $/SF | All-in site cost per acre | Typical use |
|---|---|---|---|
| Compacted crushed aggregate | $1.85 to $3.80 | $175,000 to $425,000 | Trailer, container, equipment storage |
| Recycled asphalt millings over stone | $2.20 to $4.25 | $200,000 to $450,000 | Truck parking, fleet staging |
| Heavy-duty asphalt | $4.75 to $8.00 | $325,000 to $650,000 | Truck terminal, high-turn fleet yard |
| Hybrid: concrete aisles, aggregate storage | $4.00 to $7.50 | $350,000 to $625,000 | Container handlers, heavy equipment |
| Full concrete (ACI 330 Category D) | $9.50 to $15.00 | $550,000 to $950,000 | Container yards, top-pick and reach stacker traffic |
General site work pricing, mass grading, and clearing assumptions are covered in depth in our commercial site development cost per acre guide. This page focuses on what is specific to an outdoor storage yard: the surface that carries 80,000 pound trucks, the stormwater math that gravel does not escape, and the zoning friction that decides whether the yard is allowed at all.
What is industrial outdoor storage, and why is demand so strong?
Industrial outdoor storage is land zoned for industrial use where the value sits in the yard, not the building. Tenants park tractors and trailers, stage containers, store equipment and building materials, or run fleet operations. LaSalle Investment Management describes IOS sites as having a floor area ratio under 20 to 25 percent and often zero, and Clarion Partners frames the sector as low-coverage yards, truck terminals, and last-mile sites with building coverage typically below 20 percent.
The demand data is hard to ignore. Newmark reported in September 2025 that IOS rents rose 123 percent since 2020, more than twice the rate of bulk warehouses, with vacancy about half that of bulk product. KBRA research published in September 2026 put IOS vacancy at 2.5 percent versus 6.7 percent for traditional industrial.
Supply is the constraint. Many cities have rezoned infill industrial land away from outdoor uses because yards generate fewer jobs and less tax base per acre than buildings. That scarcity is why purpose-built IOS development, and conversion of underused industrial parcels, pencils for investors right now.
| Metric | Typical range | Why it matters |
|---|---|---|
| Site size | 2 to 15 acres | Under 2 acres struggles with truck turning; over 15 acres often trades as a terminal |
| Building coverage | 5 to 15 percent | Common ceiling cited by researchers is under 20 to 25 percent |
| Building size | 2,000 to 20,000 SF | Shop, office, driver lounge, sometimes cross-dock doors |
| Usable yard | 75 to 90 percent of gross acreage | Setbacks, detention, and landscape buffers eat the rest |
| Trailer stalls per acre | 25 to 40 | Depends on aisle width and stall angle; 53 foot trailers need long drive aisles |
Gravel vs millings vs asphalt vs concrete: what does each truck yard surface cost?
The surface is the largest single line on most IOS budgets, and it is where owners over-buy and under-buy in equal measure. The right answer depends on traffic: parked trailers on landing gear, turning tractors, and container handlers with 100,000 pound front axles are three different design problems.
| Surface | Typical section | $/SF | $/acre | Service life |
|---|---|---|---|---|
| Crushed aggregate | 8 to 12 in compacted stone over geotextile | $1.85 to $3.80 | $80,000 to $165,000 | Indefinite with regrading every 2 to 4 years |
| Asphalt millings | 4 to 6 in rolled millings over 6 in stone | $2.20 to $4.25 | $95,000 to $185,000 | 5 to 10 years, ruts at turning areas |
| Heavy-duty asphalt | 4 to 5 in hot mix over 8 to 10 in aggregate base | $4.75 to $8.00 | $205,000 to $350,000 | 15 to 20 years with sealcoat and crack fill |
| Concrete | 7 to 8 in unreinforced or fiber over 4 to 6 in base | $9.50 to $15.00 | $415,000 to $655,000 | 25 to 35 years |
Compacted aggregate
Crushed stone is the IOS default for a reason. The U.S. Geological Survey's 2026 Mineral Commodity Summary puts the 2025 average unit value of crushed stone at about $18.50 per metric ton at the plant. By the time it is hauled, spread, and compacted, you are paying $30 to $55 per ton in most markets, and a 10 inch section needs roughly 2,400 to 2,600 tons per acre. Haul distance is the swing factor.
Specify a dense graded base (not clean stone), a woven geotextile over soft subgrade, and a crowned cross slope of 1.5 to 2 percent. Clean stone looks good on day one and ruts into a mud pit after the first wet season under trailer landing gear.
Recycled asphalt millings
Millings bind up once rolled and trafficked, control dust better than stone, and are cheap when a DOT milling project is nearby. They are not pavement: expect raveling and rutting at turning radii.
Heavy-duty asphalt
The Illinois Asphalt Pavement Association notes that heavy truck areas typically require a minimum full-depth design of about 8 inches of asphalt, and that truck loading areas can need a heavy-duty section even inside a light-duty lot. On a typical IOS yard with a good aggregate base, 4 to 5 inches of hot mix in two lifts is the practical floor. Asphalt hates static loads: trailer landing gear and container corner castings punch through it in summer heat, so plan concrete dolly pads along the trailer noses.
Concrete
ACI 330R places tractor-trailer entrance and exterior lanes in traffic Category D, with 20 year design thicknesses of roughly 6.5 to 9 inches depending on subgrade support and concrete flexural strength. Concrete is the right call for container handler lanes, fueling areas, wash bays, and anywhere a top-pick or reach stacker turns. It is rarely the right call for the whole yard.
Industrial Development Guide / 2026
Installed surface cost per acre
Midpoint of TCG 2026 budget range, surface only
Basis: midpoints of the per-acre ranges above; excludes grading, stormwater, and site systems.
What drives IOS yard construction cost beyond the surface?
| Line item | TCG 2026 budget range | Notes |
|---|---|---|
| Clearing, grading, earthwork | $20,000 to $75,000 per acre | Balanced site at low end; import fill or rock at high end |
| Stormwater detention and water quality | $25,000 to $90,000 per acre | Underground vaults run higher; regional ponds lower |
| 8 ft chain link with barbed wire | $40 to $65 per LF | Galvanized, 3 strand barbed arm; add for privacy slats |
| Ornamental steel or screen wall | $90 to $300 per LF | Often required on street frontage |
| Motorized cantilever slide gate with access control | $35,000 to $75,000 each | 30 to 40 ft opening, card or plate reader, loop detectors |
| LED pole lighting | $9,000 to $15,000 per pole | 30 to 35 ft poles, bases, conduit; 3 to 5 poles per acre |
| Security cameras and monitoring hardware | $25,000 to $90,000 per site | License plate cameras at gates add cost |
| Utility service and extensions | $75,000 to $350,000 per site | Three-phase power for a shop is the usual driver |
| Landscape screening and buffers | $15,000 to $100,000 per site | Driven by frontage length and code |
| Civil, survey, geotech, SWPPP, design | 6 to 10 percent of hard cost | Permit and impact fees passed through as assessed |
Stormwater: gravel does not get you out of it
This is the line item that wrecks the most IOS pro formas. Owners assume a gravel yard is pervious. Most stormwater reviewers disagree. Chapel Hill, North Carolina, for example, counts gravel driveways and parking areas as impervious and generally does not allow owners to appeal that classification for fee purposes unless the surface is engineered to be pervious. Many other jurisdictions apply the same logic to detention sizing.
Once the yard counts as impervious, you need detention to hold post-development peak flows to pre-development levels, plus a water quality treatment device in most jurisdictions with an MS4 permit. On a 5 acre yard that is commonly a dry pond taking 8 to 12 percent of the site, or an underground system that saves land and costs two to four times as much.
Separately, the EPA requires Clean Water Act permit coverage for construction that disturbs 1 acre or more, including smaller sites that are part of a larger common plan. In most states that means filing a notice of intent under the state construction general permit, preparing a SWPPP, and running inspections until final stabilization.
Utilities and fees
A pure storage yard can live on a single-phase service for gates and lights. A shop with lifts, compressors, and welders needs three-phase power, and the utility extension can cost more than the building's electrical package. Connection and impact fees are covered in our utility tap fee and impact fee guide. Lighting circuits, poles and gate power are priced like any commercial electrical scope.
Watch out: Before you price any of this, confirm the parcel is clean. Former truck terminals and contractor yards carry fuel, oil, and solvent history. Our Phase I and Phase II ESA guide explains what lenders and buyers should order.
What does the shop and office building add to an IOS project?
Most IOS tenants want a small building: an office for dispatch, a driver lounge and restroom, and often two to six maintenance bays. A pre-engineered metal building is almost always the answer because it is fast, cheap per square foot at small sizes, and easy to expand. Plan on $150 to $275 per SF as a TCG 2026 budget range for a finished PEMB shop with office, versus a shell-only number that is much lower.
Shell pricing by size and region is in our PEMB cost per square foot guide. If the tenant is a fleet that services its own trucks, the bay count, pit or lift choice, ventilation, and oil separator drive the number, and we break those down in our truck repair shop construction cost guide.
- Drive-through bays: 16 by 16 ft or 16 by 18 ft overhead doors, 80 to 100 ft bay depth for a tractor and 53 ft trailer, or 60 to 70 ft for tractor-only service.
- Oil and sand separator: required by most plumbing codes and pretreatment programs for floor drains in vehicle service areas.
- Fire code triggers: repair garages fall under IBC Group S-1, and the size, fuel type, and any lube or fluid storage drive sprinkler and ventilation requirements.
- Dock doors: if the tenant will cross-dock, budget levelers, seals, and bumpers using our loading dock equipment cost per door figures.
Is IOS allowed on your parcel? Zoning, screening and entitlement friction
Zoning kills more IOS deals than construction cost does. Attorneys at Frost Brown Todd Gibbons laid out the common traps in August 2026: outdoor storage may need conditional use or site plan approval even in an industrial district, some codes allow it only as accessory to a building-based business, and reviewers may require paved or stabilized surfaces, screening, and stormwater controls.
Screening rules can be specific and expensive. Maricopa, Arizona, for example, requires industrial outdoor storage screens at least 8 feet tall, prohibits chain link with woven slats as the screen, bars storage from front and street side yards, and sets back stored material at a 1:1 ratio to its height above the screen wall. A code like that can turn a $50 per LF chain link line into a $200 to $300 per LF masonry or precast wall on every street frontage.
- Barbed and razor wire: many codes allow barbed wire only in industrial districts, only above 6 ft, and never on frontage facing residential or public streets. Razor ribbon is often banned outright.
- Surface requirements: some cities require paving for all vehicle maneuvering areas, or paving within a set distance of the public street to control tracking.
- Lighting: full cutoff fixtures and light trespass limits at the property line are standard; dark sky ordinances add shielding and curfew rules.
Run a zoning verification and a pre-application meeting before you close. An owner's representative who has walked IOS sites through review can usually tell you within two weeks whether you are looking at a by-right permit or a six-month hearing process.
How long does it take to build an IOS yard?
A by-right gravel yard can go from contract to tenant move-in in about 6 to 9 months. Add a conditional use hearing, a paved surface, and a shop building and 12 to 18 months is realistic. State and local review times are compared in our permitting timeline by state guide.
Industrial Development Guide / 2026
IOS yard development schedule
Typical durations, TCG 2026 planning basis
What goes wrong on IOS yard projects?
Industrial Development Guide / 2026
Six expensive IOS mistakes
What they cost when they show up late
Most of these are design-phase problems. A design-build team that prices the civil plan while it is being drawn catches them before they reach the bid set.
Should you build gravel now and pave later? A decision framework
Phasing the surface is a legitimate strategy, but only if you design for it on day one. Build the grades, drainage, and detention for the final paved condition, place a quality aggregate base, and the future asphalt is a 4 to 5 inch overlay rather than a rebuild.
Industrial Development Guide / 2026
Pick a surface strategy
Match the surface to the tenant and the hold period
Lowest cost per acre, fastest to stabilize, and the base becomes the pavement base later.
Asphalt or concrete drive aisles and entries, aggregate in the parking rows.
ACI 330 Category D loads and point loads that asphalt will not carry.
Code often requires it, and it lowers dust, tracking, and maintenance claims.
Meets tracking rules while keeping the interior in stone.
Example: 5 acre IOS yard with a 10,000 SF shop
| Line item | Aggregate yard | Asphalt yard |
|---|---|---|
| Clearing, grading, earthwork | $175,000 | $200,000 |
| Yard surface (182,950 SF) | $500,000 | $1,145,000 |
| Stormwater detention and water quality | $225,000 | $300,000 |
| 8 ft chain link and barbed wire | $105,000 | $105,000 |
| Gates and access control | $110,000 | $110,000 |
| Yard lighting (16 poles) | $175,000 | $175,000 |
| Cameras and security | $60,000 | $60,000 |
| Utilities and service | $250,000 | $250,000 |
| Landscape screening | $75,000 | $75,000 |
| 10,000 SF PEMB shop and office | $1,850,000 | $1,850,000 |
| Design, survey, geotech, SWPPP (8 percent) | $282,000 | $342,000 |
| Owner contingency (5 percent) | $190,000 | $231,000 |
| Total | $3,997,000 | $4,843,000 |
| Site cost per acre, excluding building | $380,000 | $549,000 |
Note how little the stormwater line moves between the two options. That is the gravel-counts-as-impervious effect. Contingency in this example is an owner fund for unforeseen conditions, and any unused balance goes back to the owner. If you need financing context, our 2026 construction loan rate guide covers what lenders are pricing.
Glossary
- Industrial outdoor storage (IOS)
- Industrially zoned land used mainly for open-air storage of trucks, trailers, containers, equipment, or materials, with low building coverage.
- Coverage ratio
- Building footprint divided by total site area. IOS sites typically run 5 to 15 percent, versus 35 to 50 percent for a warehouse.
- Dense graded aggregate
- Crushed stone with a range of particle sizes, including fines, that compacts into a stable base. Preferred over clean stone for truck yards.
- Asphalt millings
- Recycled asphalt pavement ground off roads during resurfacing, reused as a low-cost, partially self-binding yard surface.
- ACI 330
- American Concrete Institute guidance for concrete parking lots and site paving, including thickness tables by truck traffic category.
- SWPPP
- Stormwater pollution prevention plan, required under NPDES construction general permits for sites disturbing 1 acre or more.
- Detention
- A pond, vault, or pipe system that stores runoff and releases it slowly so post-development peak flow does not exceed pre-development flow.
- Dolly pad
- A concrete strip where parked trailers rest on their landing gear, preventing the point loads from punching into asphalt or stone.
How TCG delivers IOS yard and shop projects
Terrapin Construction Group delivers industrial outdoor storage sites through design-build, which puts civil engineering, building design, and pricing under one contract. That matters on IOS because the expensive decisions, detention strategy, surface section, and power, are made on the civil plan, and we price them while they are being drawn instead of after bid day.
We self-perform pre-engineered metal building erection for the shop and office, and we are licensed in all 50 states, so a fund buying yards in Dallas, Jacksonville, and the Midwest can use one builder and one cost model across the portfolio.
For investors who already have a civil engineer and contractor, our owner's representative team reviews site budgets, zoning risk, and schedules before you go hard on a parcel. Brokers can bring us in early through the broker partner program.
Get a budget for your project
Upload plans or describe your project for a free AI estimate, or book 30 minutes with TCG to pressure-test scope, schedule, and cost before you commit.
Free AI EstimateTalk to TCGFrequently asked questions
How much does it cost to build an industrial outdoor storage yard per acre?
Building an industrial outdoor storage yard in 2026 costs about $175,000 to $425,000 per acre for compacted aggregate, $325,000 to $650,000 per acre for heavy-duty asphalt, and $550,000 to $950,000 per acre for concrete. Those TCG budget ranges cover surface, grading, stormwater, fencing, gates, lighting, cameras, utilities, and soft costs. They exclude land, permit and impact fees, and any shop or office building.
What is industrial outdoor storage (IOS) real estate?
Industrial outdoor storage, or IOS, is industrially zoned land used for truck and trailer parking, container staging, equipment storage, and fleet operations, with little or no building. Researchers including LaSalle and Clarion describe building coverage under roughly 20 to 25 percent, and most yards are built at 5 to 15 percent. Value comes from the usable, stabilized yard rather than the building.
Is a gravel truck yard cheaper than asphalt?
Yes. A compacted crushed aggregate truck yard surface runs about $1.85 to $3.80 per square foot in 2026, versus $4.75 to $8.00 per square foot for heavy-duty asphalt. On a per-acre basis that is roughly $80,000 to $165,000 for gravel and $205,000 to $350,000 for asphalt. The savings shrink overall because many jurisdictions still count compacted gravel as impervious for stormwater detention sizing.
Does gravel count as impervious surface for stormwater?
In many jurisdictions, yes. Compacted gravel used for driveways, parking, and storage yards is commonly classified as impervious because it sheds water much like pavement once trafficked. Chapel Hill, North Carolina, for example, counts gravel driveways and parking areas as impervious and generally does not allow appeals of that classification for stormwater fees unless the surface is engineered to be pervious. Confirm the local rule before sizing detention for an IOS yard.
Do I need an NPDES stormwater permit to build a truck yard?
Usually. EPA rules require Clean Water Act permit coverage for construction activity that disturbs 1 acre or more of land, or less than 1 acre when it is part of a larger common plan of development. Nearly every IOS yard exceeds that threshold, so the owner or contractor files a notice of intent under the state or EPA construction general permit and maintains a SWPPP.
How thick should concrete be for a truck and trailer yard?
ACI 330R guidance places tractor-trailer entrance and exterior lanes in traffic Category D, with 20 year design thicknesses of roughly 6.5 to 9 inches depending on subgrade strength and concrete flexural strength. Most IOS truck lanes land at 7 to 8 inches over a 4 to 6 inch aggregate base. Container handler lanes and dolly pads may need thicker, more heavily jointed sections.
How long does it take to develop an IOS site?
A by-right compacted aggregate IOS yard typically takes 6 to 9 months from contract to occupancy, including civil design, permitting, and 10 to 20 weeks of construction. Projects that need a conditional use permit, a paved surface, a three-phase power extension, and a pre-engineered metal shop building usually run 12 to 18 months. Entitlements are the most variable step.
What zoning do you need for industrial outdoor storage?
Industrial outdoor storage generally needs light or heavy industrial zoning that lists outdoor storage as a permitted or conditional use. Many cities allow it only as accessory to a building, require 8 foot screening, limit barbed wire, and bar storage in front yards. Maricopa, Arizona, for instance, requires 8 foot industrial screens and prohibits slatted chain link. Verify zoning before closing on any IOS parcel.
Sources and further reading
- Lots to Gain: Industrial Outdoor Storage is Outperforming Bulk Warehouse, Newmark
- IOS Briefing: The Emergence of Land-Driven Logistics Real Estate, LaSalle Investment Management
- Industrial Outdoor Storage (Clarion Partners research), Clarion Partners / Franklin Templeton
- Industrial Real Estate: Shifting Fundamentals and the Rise of Industrial Outdoor Storage, KBRA
- Industrial Outdoor Storage and Zoning: Seven Common Pitfalls for IOS Developers to Avoid, Frost Brown Todd Gibbons
- Stormwater Discharges from Construction Activities, U.S. Environmental Protection Agency
- Mineral Commodity Summaries 2026: Stone (Crushed), U.S. Geological Survey
- ACI 330R-08 Guide for the Design and Construction of Concrete Parking Lots (preview), American Concrete Institute
- Parking Lots: Asphalt Pavement Design, Illinois Asphalt Pavement Association
- Maricopa City Code 18.80.100 Outdoor Storage, City of Maricopa, Arizona
Cost figures labeled TCG 2026 budget range reflect Terrapin Construction Group pricing judgment for planning purposes as of November 2026, national average before regional adjustment. Actual cost depends on site, market, design, and code requirements. Get a project-specific number with the TCG AI estimator or contact TCG.

